INtime SDK Help
newfs - construct a new UFS1/UFS2 file system (newfs.rta)
INtime SDK v7.1 > INtime Utilities > DRTOS Utilities > newfs - construct a new UFS1/UFS2 file system (newfs.rta)


newfs -- construct a new UFS1/UFS2 file system  (INtime Distributed RTOS only).

Command line

newfs [-EJNUjlnt] [-L volname] [-O filesystem-type] [-S sector-size] [-T disktype] [-a maxcontig] [-b block-size] [-c blocks-per-cylinder-group] [-d max-extent-size] [-e maxbpg] [-f frag-size] [-g avgfilesize] [-h avgfpdir] [-i bytes] [-k held-for-metadata-blocks] [-m free-space] [-o optimization] [-p partition] [-r reserved] [-s size] special


The newfs utility is used to initialize and clear file systems before first use. The newfs utility builds a file system on the specified special file. (We often refer to the "special file" as the "disk", although the special file need not be a physical disk. In fact, it need not even be special.) Typically the defaults are reasonable, however newfs has numerous options to allow the defaults to be selectively overridden.


Erase the content of the disk before making the filesystem. The reserved area in front of the superblock (for bootcode) will not be erased.
This option is only relevant for flash based storage devices that use wear-leveling algorithms.
Erasing may take a long time as it writes to every sector on the disk.
Enable journaling on the new file system via gjournal. See gjournal(8) for details.
-L volname
Add a volume label to the new file system.
Cause the file system parameters to be printed out without really creating the file system.
-O filesystem-type
Use 1 to specify that a UFS1 format file system be built; use 2 to specify that a UFS2 format file system be built. The default format is UFS2.
-T disktype
For backward compatibility.
Enable soft updates on the new file system.
-a maxcontig
Specify the maximum number of contiguous blocks that will be laid out before forcing a rotational delay. The default value is 16. See tunefs(8) for more details on how to set this option.
-b block-size
The block size of the file system, in bytes. It must be a power of 2. The default size is 32768 bytes, and the smallest allowable size is 4096 bytes. The optimal block:fragment ratio is 8:1. Other ratios are possible, but are not recommended, and may produce poor results.
-c blocks-per-cylinder-group
The number of blocks per cylinder group in a file system. The default is to compute the maximum allowed by the other parame- ters. This value is dependent on a number of other parameters, in particular the block size and the number of bytes per inode.
-d max-extent-size
The file system may choose to store large files using extents. This parameter specifies the largest extent size that may be used. The default value is the file system blocksize. It is presently limited to a maximum value of 16 times the file system blocksize and a minimum value of the file system blocksize.
-e maxbpg
Indicate the maximum number of blocks any single file can allocate out of a cylinder group before it is forced to begin allocating blocks from another cylinder group. The default is about one quarter of the total blocks in a cylinder group. See tunefs(8) for more details on how to set this option.
-f frag-size
The fragment size of the file system in bytes. It must be a power of two ranging in value between blocksize/8 and blocksize. The default is 4096 bytes.
-g avgfilesize
The expected average file size for the file system.
-h avgfpdir
The expected average number of files per directory on the file system.
-i bytes
Specify the density of inodes in the file system. The default is to create an inode for every (2 * frag-size) bytes of data space. If fewer inodes are desired, a larger number should be used; to create more inodes a smaller number should be given. One inode is required for each distinct file, so this value effectively specifies the average file size on the file system.
Enable soft updates journaling on the new file system. This flag is implemented by running the tunefs(8) utility found in the user's $PATH.
-k held-for-metadata-blocks
Set the amount of space to be held for metadata blocks in each cylinder group. When set, the file system preference routines will try to save the specified amount of space immediately following the inode blocks in each cylinder group for use by metadata blocks. Clustering the metadata blocks speeds up random file access and decreases the running time of fsck(8). By default newfs sets it to half of the space reserved to minfree.
Enable multilabel MAC on the new file system.
-m free-space
The percentage of space reserved from normal users; the minimum free space threshold. The default value used is defined by MINFREE from , currently 8%. See tunefs(8) for more details on how to set this option.
Do not create a .snap directory on the new file system. The resulting file system will not support snapshot generation, so dump(8) in live mode and background fsck(8) will not function properly. The traditional fsck(8) and offline dump(8) will work on the file system. This option is intended primarily for memory or vnode-backed file systems that do not require dump(8) or fsck(8) support.
-o optimization
(space or time). The file system can either be instructed to try to minimize the time spent allocating blocks, or to try to minimize the space fragmentation on the disk. If the value of minfree (see above) is less than 8%, the default is to optimize for space; if the value of minfree is greater than or equal to 8%, the default is to optimize for time. See tunefs(8) for more details on how to set this option.
-p partition
The partition name (a..h) you want to use in case the underlying image is a file, so you do not have access to individual partitions through the filesystem. Can also be used with a device, e.g., newfs -p f /dev/da1s3 is equivalent to newfs /dev/da1s3f.
-r reserved
The size, in sectors, of reserved space at the end of the partition specified in special. This space will not be occupied by the file system; it can be used by other consumers such as geom(4). Defaults to 0.
-s size
The size of the file system in sectors. This value defaults to the size of the raw partition specified in special less the reserved space at its end (see -r). A size of 0 can also be used to choose the default value. A valid size value cannot be larger than the default one, which means that the file system cannot extend into the reserved space.
Turn on the TRIM enable flag. If enabled, and if the underlying device supports the BIO_DELETE command, the file system will send a delete request to the underlying device for each freed block. The trim enable flag is typically set when the underlying device uses flash-memory as the device can use the delete command to pre-zero or at least avoid copying blocks that have been deleted.
The following options override the standard sizes for the disk geometry. Their default values are taken from the disk label. Changing these de- faults is useful only when using newfs to build a file system whose raw image will eventually be used on a different type of disk than the one on which it is initially created (for example on a write-once disk). Note that changing any of these values from their defaults will make it impossible for fsck(8) to find the alternate superblocks if the standard superblock is lost.
-S sector-size
The size of a sector in bytes (almost never anything but 512).


newfs /dev/ada3s1a

Creates a new ufs file system on ada3s1a. The newfs utility will use a block size of 32768 bytes, a fragment size of 4096 bytes and the largest possible number of blocks per cylinders group. These values tend to produce better performance for most applications than the historical defaults (8192 byte block size and 1024 byte fragment size). This large fragment size may lead to much wasted space on file systems that contain many small files.

See Also

M. McKusick, W. Joy, S. Leffler, and R. Fabry, "A Fast File System for UNIX", ACM Transactions on Computer Systems 2, 3, pp 181-197, August 1984, (reprinted in the BSD System Manager's Manual).


The newfs utility appeared in 4.2BSD.
See Also